Local
The Curb at the End of Your Drive
It is Village property, it was built before your driveway was, and every new, wider or relocated drive on a curbed street has to change it. What kind you have, what the code allows, and who is permitted to touch it.
Most people planning a driveway think about the slab, a few think about the apron, and almost nobody thinks about the curb. Yet on any street in the Village with curb and gutter, the curb is the last thing your tyres cross, and changing a driveway almost always means changing a length of it. Pleasant Prairie has a whole article of its code on exactly this, with its own licence, bond and insurance, separate from the rules for the approach. If you are widening, moving or adding a concrete driveway, this is the piece of public concrete that comes with it.
Two kinds of curb, and why it matters which you have
The Village code defines both types precisely, and the difference between them decides what work is needed where a drive meets the street.
| Curb type | Height at back | Height at street | Curb plus gutter width | At a driveway |
|---|---|---|---|---|
| Mountable | 11 in | 8 in | 30 in | Stays as built unless the Village permits a saw cut |
| Vertical face (Type D) | 12 in | 7 1/2 in | 30 in | Replaced with a depressed curb head, or the head saw cut |
A mountable curb has a sloped face. The code is candid about why: it lets a street be built before anybody knows where the driveways will go, and it can be driven over with care. That is why many newer subdivisions have it throughout. On those streets the curb in front of a new drive is often left alone, and the approach simply meets it.
A vertical face curb is a square step. It carries water the same way but also marks a hard edge for the road, and nobody wants to bump over it twice a day. So where a driveway crosses one, the curb head has to come down, either by taking out the section and pouring a lowered one or by sawing the top off in place.
How the curb gets changed
The code allows two methods and is strict about the details of both.
Remove and repour. Curb may be taken out in sections, without any saw cutting, and poured again as part of the driveway approach. The new back is set an inch and a half higher at the house side than the pan of the gutter, which keeps street water in the gutter rather than letting it run up your drive. Sections were originally poured in lengths of about ten feet, so the work follows those joints rather than cutting an arbitrary gap.
Saw the head. On some curbs the top can be sawn off in place instead. That needs approval from Public Works first, has to be done with a saw made for the purpose, and is ruled out entirely on a section that is already cracked or broken. A damaged section comes out and is replaced back to the nearest joint. The code says specifically that a handheld concrete saw is not acceptable for this, and it is one of the easier things to notice if you happen to be home when the crew arrives.
The paperwork, in one table
Curb work sits in its own article of Chapter 305, with requirements that are not the same as those for the sidewalk and approach. The figures below are as the code states them.
| Requirement | Curb work (Art. V) |
|---|---|
| Licence | From the Village Clerk; contractor must be prequalified; no fee for the licence |
| Surety bond | $10,000 |
| Liability insurance | At least $1,000,000, with the Village named as an additional insured |
| Permit | Required before work starts; fee set by the Village fee schedule |
| Inspections | Public Works before work begins and again after it is complete |
The insurance line is the one worth noticing. It is a higher threshold than the cover asked of firms that only build sidewalks and approaches, so a contractor properly set up for approach work is not automatically set up for the curb. Ask about both. A firm that works in the Village often will answer without looking anything up.
Where this shows up on your job
Not every driveway project touches the curb. Replacing a drive on exactly its old footprint, where the curb is already lowered and sound, usually does not. These do:
- Widening at the street. The new width runs past the lowered section, so more curb has to come down, in whole sections.
- Moving the entrance. The old opening is restored to a full curb and a new one is made. That is two lots of curb work, not one.
- A second opening or a loop. Each opening is its own curb change, with its own permit and inspection.
- A cracked or settled curb in front of the drive. It cannot be saw cut, so it comes out to the nearest joint as part of the approach.
Timing and order
Because Public Works inspects before the curb is touched, the permit and that first inspection have to fit in ahead of the crew, not alongside it. On a replacement that is easy to build into the schedule. On a job booked into a gap at short notice, it is exactly the step that gets skipped, and an inspection that never happened cannot be done after the curb is gone. Agree in writing who applies, and do not let the breaker come out until the permit is in hand.
The curb is also where the approach, the gutter and the street all meet, which makes it the place where water behaviour is decided. That inch and a half at the back is not fussiness; it is what keeps a heavy rain in the gutter where it belongs.
What to ask a bidder
- Is the curb in front of us mountable or vertical face, and does it need to change?
- Are you licensed with the Clerk for curb work, and do you carry the cover it requires?
- Will you remove whole sections, or saw the head, and have you asked Public Works?
- Is the curb permit a separate line in your price?
A bidder who answers those four crisply has done this here before. The wider rules for the stretch between the curb and your property line are in the Village approach rules, and the reasons you might be moving an entrance at all are covered in is a second entrance worth it. For the driveway itself, from the curb line to the garage door, the place to start is our concrete driveway page.
Sources
- Village of Pleasant Prairie Code, Ch. 305 Art. V, Curb Cuts - curb definitions and dimensions, permitted modifications, permit and inspections, licence, bond and insurance. Read 24 September 2026.
- Village of Pleasant Prairie Code, Ch. 305, Attachments 1 and 3 (details RD-17 and RD-12) - curb head saw-cut approval, damaged sections, saw type, and what happens to each curb type at a driveway. Read 24 September 2026.